![ic-756 pro ii reset ic-756 pro ii reset](https://icomuk.co.uk/images/Icom/product/productImageLarge/IC_756PRO3_850x365.jpg)
Receive Audio is for some reason, SUPERB- even to my 7600. Slow SCOPE really is no big deal, actually it's better with a Slower Scope, it's not so distracting.
![ic-756 pro ii reset ic-756 pro ii reset](https://i.ytimg.com/vi/IZxt55eKXN8/maxresdefault.jpg)
Farson VA7OJ/AB4OJ created this page.Better sounding audio than the 7300 I sold, or even the ICOM 7600 I still have!
IC 756 PRO II RESET DOWNLOAD
Otherwise, the IC-756Pro II’s default address of "64h" can be used.ĭo not use the IC-756Pro II’s tuner when using the IC-PW1.Ĭlick "Get IC-PW1 Info" bar (below) to download IC-PW1 user & service manuals, etc.Ĭontents copyright © 2004 George I. If interfacing the IC-756Pro II to WriteLog software, a CI-V address of "5ch" must be used. I recommend reducing theIC-756Pro II’s power level if this happens, so as to keep from stressing the IC-PW1 during tuning. If you press TUNER to activate theIC-PW1’s tuner 2 and hit the key, you may see the SWR meter go to infinity ( ∞) momentarily until the tuner tunes. Press the AMP/PROTECT switch on the IC-PW1 and you will be ready to transmit. It is critical that the units are powered off and on in the exact sequence described in the procedure. Recheck all cabling, including the ACC cable and the Remote cable, and repeat steps 2 and 4 above. If at this point, the IC-PW1 does not automatically follow band changing in the IC-756Pro II, the units are not insync. Switch to a different band on theIC-756Pro II, and the IC-PW1 will automatically switch to that band. For example, if the 21MHz band is displayed on the IC-756Pro II, the IC-PW1 will switch to the 21 MHz band, and the 21 lamp will turn on. At this point, the AUTO lamp on theIC-PW1 will be on, and the IC-PW1 will switch to the same band as the IC-756Pro II. The IC-756Pro II and the IC-PW1 will now be in sync. If the INPUT 1 lamp continues to flash, make sure CI-V Transceive=ON in theIC-756Pro II. Turn the transceiver’s main tuning knob until the INPUT 1 lamp stops flashing on theIC-PW1. Wait for the transceiver to cycle on and display the BandScope. This will turn theIC-PW1 on and the INPUT 1 light will now be flashing. On the IC-PW1, while holding down the INPUT button, push the POWER button. IC-PW1 user manual.) First of all, make sure the following conditions are set in the IC-756Pro II’s EXIT/SET OTHER menu: To set up this automatic tracking capability, the IC-PW1 must be programmed to be in sync with the IC-756Pro II. The IC-PW1 uses CI-V frequency data for automatic tracking of band changes in theIC-756Pro II. Doing so will provide little more power and will probably cause the amp to fault off. Do not set it higher than the "ALC (adj.)” point on the METER-2. Set the IC-PW1’s ALC level as described on p.11 of the IC-PW1 user manual. Use the thumb and little finger on the right hand to simultaneously hold the DOWN and UP buttons while pushing POWER with a finger on your left hand.
![ic-756 pro ii reset ic-756 pro ii reset](https://www.ab4oj.com/icom/ic756pro3/images/p3scope.gif)
On the IC-PW1, push POWER while holding the DOWN and UP buttons. If the IC-PW1 is on, push POWER to turn the IC-PW1 off. (This is described on p.11 ofIC-PW1 manual.) Here are the steps: When first applying power to the IC-PW1, its CPU must be reset. TheIC-756Pro II’s ACC(2) jack must be used. If the IC-756Pro II ACC(1) jack is used by mistake - a very easy mistake to make - no ALC will be available, and the amp will be driven to 1600 watts, which it is not designed to handle. It is critical that the ACC cable be connected from the IC-756Pro IIACC(2) jack to the IC-PW1 ACC-1 jack.
![ic-756 pro ii reset ic-756 pro ii reset](https://www.dxzone.com/dx32367/the-ic-756pro-iii.jpg)
What follows are suggestions and recommendations regarding the setup and use of these units.Ĭonnect all cables between the IC-756Pro II and the IC-PW1 as shown on p.7 of theIC-PW1 manual.
IC 756 PRO II RESET MANUAL
Synchronizing the IC-756Pro II to the IC-PW1 can be tricky in the sense that if the procedures outlined in theIC-PW1 manual are not followed exactly, the IC-PW1 will not automatically follow band changing on theIC-756Pro II. It is possible to make mistakes in the hook up and operation of theIC-PW1 that can lead to problems. However, after a couple of years of experience in running this combination, I have learned a few things that are worthy of passing onto others. Operation of the Icom IC-756Pro II with the Icom IC-PW1 amplifier is excellent. Icom IC-756Pro II - IC-PW1 Sync Procedures byGeorge I. Icom IC-756Pro II - IC-PW1 Sync Procedures